The UVLED furnace is also called LEDUV curing furnace and UVLED oven. Here "UVLED" is an English abbreviation for LED ultraviolet rays. CICS refers to the process of changing material from low molecules to polymer. UV curing generally requires the curing conditions or requirements of ultraviolet curing coatings (paint), adhesive (glue) or other seal sealing agents. The role and advantages of UVLED furnace equipment 1. The difference between UVLED light sources and traditional high -pressure mercury light curing equipment A: The UV light generated by traditional curing machines looks bright and the calories are very high. In fact, its spectral spectrum is wide. A certain ultraviolet spectrum segment that truly solidified only accounted for part of its energy. A considerable part of the visible light segment (miscellaneous) and generated heat, which was severely damage to the operator and easily deforms the heat of processing workpieces. B: The UVLED furnace is a high -purity single -wave length ultraviolet light, which belongs to the cold source; the temperature of the workpiece is only about 3 degrees, and the processing parts will not be deformed. The solidification effect of high-pressure mercury lamps of 1000-2000mW of 1000-2000mW is comparable, which shortens the curing time to 0.5S2 and UVLED furnaces significantly reduced production costs. Life) Energy -saving design, only when it needs to be illuminated, the power consumption is low, and the power: about 50W. B: The UVLED furnace body is small and light, which can easily integrate it into the automatic assembly process, or use it as a complete desktop system. C: The LED irradiation head is controlled by the computer. You can choose manual or automatic control according to actual needs, and set the time required for light irradiation (accurate to 0.01S) to further support high -precision junction needs, reducing the time error of human operation time errors. More information is welcome to log in

As a new technology, UVLED is widely optimistic about its sustainable development. Its environmental protection, low energy consumption, environmental protection of raw materials. It has made great progress in environmental protection aspects. Flexible sealing is the two ends connected to the LCD display and the driver integrated circuit with flexible wires or band -type wires. Due to the effect of dust or humidity, it is easy to cause interference. UV ultraviolet light curing adhesives used for flexible seals should have low viscosity, which is convenient for flowing into the protected area, good adhesion, high purity, and no pollution. The well -combined combination of UV glue and UVLED optical curing equipment, which can most effectively complete and meet the requirements of flexible sealing. At present, environmentally friendly coatings basically develop to two roads, one is water -based paint, and the other is UV curing coatings. Water -based paint, as the name implies, is to use water for solvents, so during use, it can greatly reduce the existence of harmful substances. UV curing coatings are the aggregation and cross -linking reactions between the low molecular premature or cluster in the coatings of the ultraviolet light to cause the low molecular premature or cluster in the coating to obtain the hardening paint film, so as to achieve it No harm. However, because there are few categories and less publicity, many consumers do not understand at all. At present, environmentally friendly coatings can not be widely spread, and many consumers do not understand their excellent nature. UV curing coatings are so environmentally friendly, is there no disadvantage? Of course, the answer is "No". The first patent of UV curing coatings was born in 1947. After more than half a century of development, UV curing coatings have become more mature technology. Especially with the improvement of people's environmental awareness, production and researchers have paid more attention to UV curing coatings. Development and application. UV curing coatings are a green and environmentally friendly coating. It fully meets the "4E" principle. Generally, UV curing energy consumption is a small part of thermal curing, and UV curing coatings contain less volatile components, small pollution, the most attractive researchers And developers are UV curing coatings to reduce raw material consumption, which is conducive to reducing economic costs. UVLED optical curing technology is a photochemical reaction, which is similar to the traditional drying process, but the principle is different. The traditional drying process is generally the process of coating material due to the volatile of the solvent; The reaction of aggregation and radiation crosslinks quickly transforms low -molecular weight substances into a chemical process of polymer substances, which makes UV glue or ink change from liquid or semi -liquid to solid or semi -solid state. The UV curing system does not contain solvents or contains a very small amount of solvents. After irradiation of ultraviolet light, the liquid film can be solidified almost 100%. UVLED curing light sources in existing technologies usually use wind cooling or water cooling. Among them, the water cooling and wind -cooling method for UVLED curing light sources is better. As an environmental protection technology, people are committed to promoting it extensively. Make it widely app. Now UVLED technology has begun to slowly replace the market for traditional mercury lamps. Zhuhai TIANHUI Technology Development Co., Ltd. specializes in UVLED, UVLED wire light sources, UVLED face light sources, UVLED dot light sources, UV point light sources, UVLED light sources, UVLED curing machines, ultraviolet curing machines, UVLED ovens development, production, sales and technical services , Is a professional UV -point light source manufacturer, UVLED manufacturer, UVLED manufacturer. Welcome colleagues in various industries to call for letters to inquire!

The development of UVLED light source technology in the metal processing industry has always received great attention from people. Metal processing has always been an industry with high technical content and operation requirements. UV curing technology just fills the shortcomings of this aspect. The adhesion of the metal lead terminal is to put the metal nail into the glass, and coat it with UV adhesive. Although this adhesion does not have the above -mentioned strict requirements for the direct contact with the adhesive and the LCD material, it is required to be moderate viscosity, not flowing after the glue, and the drying of the surface when the UV is cured, good electrical insulation, and the viscosity of glass and metals. High intensity and excellent humidity and heat aging performance. In the non -color formula, the competition between the pigment and the UVLED trinion absorbs ultraviolet light, which will affect the utilization rate of the UV light cause of the light, and then affect the concentration of the free radicals that can be generated. Different pigments have different absorption rates and transmission rates for different wavelengths. The smaller the absorption rate of the pigment, the greater the light transmission rate, and the less loss of the light energy. Carshrilia's ultraviolet absorption capacity is high, the slowest solidification, strong white pigment reflector, which also hinders solidification. Generally speaking, the order of absorption of ultraviolet light is: black, purple, blue, blue, green, yellow, red. When the amount of pigments is too large, the curing of the surface layer of the paint film is not affected, but the deep energy obtained by deep layers is very small. The deep curing of the paint film is greatly affected. The pre -drying level before UVLED optical curing has a great impact on the performance of the curing film. When the drying is incomplete, it slows down the UV optical curing speed. This is because although water has a certain effect on the convergence of oxygen inhibitory oxygen, this can only be this can only be Make the surface of the ink membrane quickly solidify, that is, it is just dry, but it cannot achieve practical dryness. Because the water contained in the membrane is difficult to escape, it makes it difficult for the curing film to become uniform and continuous. The existence of water makes the membrane temperature lower, which is not conducive to improving the conversion rate of gel. Therefore, the control of the formula water content is not only the requirements of the formula stability, but also consider drying efficiency. After the metal processing industry has introduced UVLED optical curing technology, it has made great development. Make the production capacity and product quality of the metal processing industry greatly improved. As the current industry -leading manufacturer in China, Tianhui provides a solution from the entire industry UVLED solution and provides in -depth customer customization services. If you have any questions about ultraviolet solidification applications, you can contact us. The industry is bigger and stronger!

The LED -type UV curing machine produced by Tianhui is a UV curing machine made of LED light sources. Its working principle is that under the irradiation of UVLED ultraviolet light, photons (such as 365nm, 395nm, etc.) with specific wavelengths of light cause agent absorb specific wavelengths, which stimulates to stimulate the state, forms free radicals or cations, and then transmits through the energy between molecular energy to make the aggregation. Premier and sensitivity monomers have become exciting, generating charge transfer collaterals. These collateral fittings are constantly cross -linking agglomerations to generate polymer polymers solidified into a three -dimensional mesh structure in a very short time. At present, the market is mainly in the market: UVLED point light source curing machine, UVLED wire light source curing machine, UVLED face light source curing machine, UVLED oven, UVLED furnace, UVLED conveyor belt, etc. Compared to the traditional UV mercury lamp curing machine, Tianhui's UVLED curing machine has the characteristics of soft light, long life, energy saving, safe and environmentally friendly, wide -ranging area, small space, uniform light spots, etc. The LED light UV curing machine emits only about 15 watts of energy consumed when a certain brightness is reached, and the traditional light reaches the same brightness to consume 1500 watts of energy. The service life is as high as 2000 hours, which is about 10 times the traditional lamps. UVLED curing machine applications include UV adhesives in industries such as display, electronic medical care, instrumentation and other industries; UV coatings in buildings, furniture, home appliances, automobiles and other industries;. In addition, it can also be used in many fields such as silk -printed curing, coding curing, exposure solidification, and home furnishings. With national policy orientation and everyone's awareness of environmentally friendly green production, the UVLED -style curing process has also shown an increasing trend. As the provider of the UVLED industry application plan and product, Tianhui has done its best to improve the cost -effectiveness of the product and create value for customers in the industry.

UVLED solidification, the main condition is that the molecular absorption of light quantum with sufficient energy becomes a stimulus molecule, decomposes into free radicals or ions, so that unsaturated organic objects are used for aggregation, branches, cross -linking and other chemical reactions, so as to achieve the purpose of solidification. 1. The UVLED energy required by the Knowing Optical Discovering agent is to ensure thorough solidification, the energy scientific and reasonable energy provided by the supply is normal than the energy it needs. 2. I do not know the UVLED energy required by the light caused by the light cause, and the supply is the supply blindly. Methods not only waste energy, but also cause negative effects of excessive solidification, such as explosion gathering, anti -aggressive reactions, etc. 3. When UVLED is insufficient, the energy of UVLED must be moderate, that is, it cannot be excessive or insufficient. 4. Compared with traditional mercury lamps and halogen lights, UVLED belongs to the one -wavelength ultraviolet rays. The wavelength width is small. It is generally about 5nm in the positive and negative 5nm. Choose the UVLED wavelength that matches the light cause. 5. In the process of curing, the optical cause needs to be completely solidified at one time. If the ultraviolet energy is too small, the solidification effect is not good. It is recommended to adjust the UVLED curing energy again. UVLED's curing time, etc. For more uvled information, please contact Tianhui!