[Cold Transfer] UV Cold Transfer ---- a Very Promising Technology

UV cold transfer refers to a method that uses UV -optical curing adhesives to transfer. This technology can be widely used in many industries such as crafts, craft paintings, decoration, metal paint, photography, signing license plates, and advertising. UV cold transfer required equipment and consumables: 1. Computer: ordinary configuration 2. Inkjet printer: such as Epson 830U, etc. 3. Transfer use of UVLED light source LX-S33072 4. Print dedicated transparent film: This membrane is this film is as a film is this film is a film. Two layers of structure, one of which is a thick PET (polyester) duct, and the other is a very thin soft film with water absorption characteristics, preventing the phenomenon of piles when printing. 5. UV Cold Transcover Special UV cite glue (such as TU-102, TU-103, TU-107, etc.) 6. UVLED curing glue (such as UV-100, YK-300, etc.) on the surface protection Rolling: The rubber plastic scraper or roller used on the UV silk screen printing, or the self -made or using a rubber phone card, etc. instead. The advantage of UV cold transfer is: 1. Simple operation and fast operation: no need to make any versions, no mechanical equipment, can be printed with inkjet printer, which is very easy to transfer with the required substrate surface of the substrate. You can transfer a picture of A4 paper size. It only takes a few minutes from the version of the version to the product to complete. 2. It can be fully personalized, because there is no need to make a version, even if a product is made, it can be transferred. 3. Applicable substrate materials are widely transferred: almost any surface panels or products that can be expanded for flat panels, such as glass, ceramics, metal, wood, stone, plastic, etc. 4. There are almost no pixels and color loss during the transfer process. Any method designed or downloaded online, as long. 5. The transposed graphic surface is water -resistant, and the injury resistance and goodness can achieve the degree of human fingernails, metal copper and aluminum, etc. 6. A transparent background transfers can be performed. If you transfer it to transparent glass or plastic, the effect is clear and transparent. When transferred on the surface of gold, silver or other colors, its background color can be kept completely. 7. The transfer area can be large or small. (At present, Epson has a printer that can print with a wide range of graphics above 1 meter. ) Typical basic operation method (program): 1. Print the required graphics and text on a dedicated transparent film. 2. Apply an appropriate amount of special glue TU-103 on the prepared bears. 3. Cover the film and text on the glue. 4. Scrape the rubber (scraped hard) with a rubber and plastic scraper (to be scraped hard) at the same time. 5. Put it under UV light for 3-5 minutes. 6. Leave the light source, cut off the flying edge, and unveil the PET membrane (at this time the film has become a transparent film, the graphic has been transferred to the bearing material. (This unveiled PET membrane is carefully stored on the side to wait for the lane process) 7. Solving the TU-103 glue for a small amount of appropriate amount on the already transferred pattern again, cover the PET film, scrape the average, solve the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, remove the light, and remove the light. PET membrane. (The purpose of this plastic layer is to increase the adhesion of the surface glue (such as UV-100) 8. Apply the UV-100 on the above pattern, and slowly put the PET membrane slopes. Fill the entire picture, use the PET membrane's own gravity to apply the rubber fluid evenly. Check if there are bubbles, if so, you need to try to remove. 9. Put it under UV light for 2-4 minutes. take out. Reveal the PET film. 10. Use the 600 -purpose diamond sand to polish, polish, wash, finished. (This process can be carried out by hand by hand by hand and the corresponding polishing equipment.) UV cold transfer cost problem: use UV cold transfer to make a picture of 20cm 30cm area: film, ultraviolet light A total of about 3-5 yuan for curing glue and printing ink. Other instructions: 1. The above is a common UV transfer method. This method is actually a fake transfer, because it is a soft film that prints the graphic on the film. The soft film is transferred from the film to the need to be in the printed matter. If you want to realize the true transmission, you should print the graphic with a laser printer. 2. Surface smoothness depends on the surface level of the PET membrane, and the general PET membrane can achieve the mirror effect. 3. Due to the strength of ultraviolet light, the power of the light source can be reduced to reduce the curing time to within one second. Factors affecting the quality of the final finished product: rubber model and its quality, film quality, surface cleanliness, construction method, whether the construction method, curing (lighting distance and light intensity), and water may produce the quality of the final product. influences. Therefore, a special adaptive test must be performed before mass production to determine the best model selection and implementation plan. For more LED UV information, please consult Tel: