The main highlights of LED lamps BAI: energy saving, long DU life, environmental protection, and light color control ZHI. As LED is a new type of DAO product of high -tech lighting in the 21st century, production technology is still increasing. 4014LED lamp beads are customized 1, power: 4014LED lamp beads do 0.2W2, highlight: 4014 brightness 22-26LM 3, heat dissipation: the bottom there are heat sinks, but 4014 is a thermal power separation design, the heat dissipation effect. Precautions for LED lamp beads: 1. All operators who need to touch the LED lamp bead must wear a truly effective anti -static bracelet. 2. If there is a bending need for LED pins, the folding point is more than 3mm from the LED colloid; 3. The normally required welding of LED±At 3 C, the welding time must not exceed 2 seconds. If it is crossing the tin furnace, the temperature of the tin furnace is less than 275 C, and the time for soaking tin must not exceed 2 seconds. 4. When the LED is over -welded, the wave welding machine is required to be truly grounded. When the grounding line, you cannot connect to the ground line of the municipal grid. You must connect to a real ground line completely separated from the municipal grid ground line. 5050RGBLED Patch Lighting Bead Parameters-4014LED Lighting Ball Supply and Marketing. The application of 3528LED lamp beads main lamp bar, light source and other industries, the parameters and performance descriptions of 3528LED lamp beads are mainly from two aspects, one is brightness, the second chip and size. 3528LED lamp bead advantages and disadvantages analysis: (1) light spot: 3528 thickness is 1.8mm, mainly to light emitting, making sunlights more likely to produce light spots There are light spots) (2) heat dissipation performance: 3528 patch has poor heat dissipation performance, and a layer of plastic between the bottom heat sink and the chip, so the heat dissipation performance is poor, and the number of lamps used in the light lamp tube is large, so it is tidy The lamp heat dissipation performance is also poor. Everyone knows that the life of LED lamps is mainly the temperature, so the life of the lamp tube is very harmful. (3) Cost of the lamp: The cost of making a fluorescent lamp tube is higher and the light effect is lower. For example, a 20W LED fluorescent lamp requires 288 capsules for 3528, and the cost of the 3528 light source of 7-8LM is: 288 grains*0.13 yuan/grain = 37.44 Yuan, the brightness of the whole light is: 288 grains*7.5LM (the intermediate value of the brightness of a single lamp bead)*0.9 (power power factor)*0.85 (out of light) = 1652.4LM (the brightness of the whole light is about 1600lm) ; 3528LED is used in the field of indoor lighting, commercial lighting, industrial lighting. Such as LED lighting products, LED decoration products, LED backlight products, lighting lighting, backlight display (LCD, billboard), car lights, etc. Although 4014 patch lamp beads are small in size, they have the characteristics of high brightness, low calories, etc. This is due to the composition of the 4014 patch lamp bead. The advantages and characteristics of the new 4014LED lamp bead product: 1. High brightness: single 0.2W, 4014LED lamp beads can be as high as 26LM. 2. Good heat dissipation: 4014LED lamp beads have a special structural design, and the heat dissipation effect is good. In addition to the heat dissipation spots at both ends, there is also a large amount of heat sink in the middle. 3. Low attenuation: Use the industry's raw materials, automated equipment, the product continuously lit test 3000 hours attenuation is less than 1%, 5000 hours lower than 3%. 4. Long life: The effective service life of the product can reach 40,000-50000 hours. Precautions for LED lamp beads: 1. All operators who need to touch the LED lamp bead must wear a truly effective anti -static bracelet. 2. If there is a bending need for LED pins, the folding point is more than 3mm from the LED colloid; 3. The normally required welding of LED±At 3 C, the welding time must not exceed 2 seconds. If it is a tin furnace, the temperature of the tin furnace is less than 275 C, and the time for soaking tin must not exceed 2 seconds. It is required that the operator's movement is very skilled and accurate. 4. When the LED is over -welded, the wave welding machine is required to be truly grounded. When the grounding line, you cannot connect to the ground line of the municipal grid. A real ground line is completely separated from the municipal grid ground line.
Author: Tianhui-Air Disinfection
Author: Tianhui-UV Led manufacturers
Author: Tianhui-UV water disinfection
Author: Tianhui-UV LED Solution
Author: Tianhui-UV Led diode
Author: Tianhui-UV Led diodes manufacturers
Author: Tianhui-UV Led module
Author: Tianhui-UV LED Printing System
Author: Tianhui-UV LED mosquito trap